DF14 wire connector crimp terminals with 1.25mm pitch, gold-flash phosphor bronze terminals

Pitch 1.25mm Tin-plated or Gold- flash wire connector terminal

Category: Crimp Terminals
Series:A1253-TPEor A1253-GPE
Application:Signal
Material :Phosphor Bronze
Finish:Tin-plated or Gold-flash
Packaging Type: Reel
Termination Interface Style: Crimp or Compression
Wire Insulation Diameter:1.00mm(max)

Electrical & Mechanical information:
Current Rating: 1A AC, DC
Voltage Rating: 150V AC, DC
Contact Resistance: 30mΩ Max
Insulation Resistance:500MΩ Min
Withstanding Voltage: 500V AC/minute

Temperature range: -25℃ to 85 ℃

Ordering Information:

Drawing & testing report:

Please kindly check the following information to order right products.

1. Scope This specification covers the requirements for product performance of 2.00mm pitch wire to board connectors series. 2. Construction,Dimensions,Material & Plating See the attached drawings 3. Ratings & Applicable Wires Item Standard Rated Voltage (Max.) 100V AC/DC Insulation O.D. 1.50mm (Max.) Rated Current (Max.) And Applicable Wires AWG#24 2.0A AC/DC AWG#26 1.5A AC/DC AWG#28 1.0A AC/DC AWG#30 0.5A AC/DC Ambient Temperature Range -25℃ ~ +85℃* *: Including terminal temperature rise 4. Electrical Performance Test Description Procedure Requirement 4-1 Contact Resistance Mate connectors, measure by dry circuit, 20mV max., 10mA.(Based upon JIS C5402 5.4) 10mΩ (Max.) 4-2 Insulation Resistance Mate connectors, apply 500V DC between adjacent terminal or ground. (Based upon JIS C5402 5.2/MIL-STD-202 Method 302 Cond. B) 1000MΩ (Min.) 4-3 Dielectric Withstanding Voltage Mate connectors, apply 800V AC (rms) for 1 minute between adjacent terminal or ground. (Based upon JIS C5402 5.1/MIL-STD-202 Method 301) No Breakdown. 4-4 Contact Resistance on Crimped Portion Crimp the applicable wire on to the terminal, measure by dry circuit, 20mV (Max.)., 10mA. 5mΩ (Max.) 5. Mechanical Performance Test Description Procedure Requirement 5-1 Actuator Insertion & Withdrawal Force Insert and withdraw connectors at the speed rate of 25±3mm / minute. Refer to paragraph 7-2 5-2 Crimping Pull Out Force Fix the crimped terminal, apply axial pull out force on the wire at the speed rat of 25±3mm / minute.(Based upon JIS C5402 6.8) AWG#24 3.0kgf (Min) AWG#26 2.0kgf (Min) AWG#28 1.0kgf (Min) AWG#30 0.8kgf (Min) 5-3 Terminal Insertion Force. Insert the crimped terminal into the housing. 1.00kgf (Max.) 5-4 Terminal/Housing Retention Force. Apply axial pull out force at the speed rate of 25±3mm / minute on the terminal assembled in the housing. 1.50kgf (Min.) 5-5 Pin Retention Force Apply axial push force at the speed rate of 25±3mm / minute 1.00kgf (Min.) 5-6 Durability When mated up to 50 cycles repeatedly by the rate of 10 cycle per minute. Contact Resistance 20mΩ (Max.) 5-7 Vibration Amplitude: 1.5mm P-P Sweep time: 10-55-10 Hz in 1 minute Duration: 2 hours in each X.Y.Z. axes. (Based upon MIL-STD-202 Method 201A) Appearance No Damage. Contact Resistance 20mΩ (Max.) Discontinuity 1 μsec.(Max.) 5-8 Physical Shock 490m/s²｛50G｝,3 strokes in each X.Y.Z. axes. (Based upon JIS C0041/MIL-STD-202 Method 213B Cond. A)

6. Environmental Performance And Others Test Description Procedure Requirement 6-1 Temperature Rise Carrying rated current load.(Based upon UL 498) 30℃(Max.) 6-2 Heat Resistance 85±2℃,96 hours (Based upon JIS C0021/MIL-STD-202 Method 108A Cond. A) Appearance No Damage. Contact Resistance 20mΩ (Max.) 6-3 Cold Resistance -25±3℃,96 hours (Based upon JIS C0020) 6-4 Humidity Temperature: 40±2℃ Relative Humidity : 90~95% Duration: 96 hours (Based upon JIS C0022/MIL-STD-202 Method 103B Cond. B) Appearance No Damage. Contact Resistance 20mΩ (Max.) Insulation Resistance 100MΩ (Min.) Dielectric Withstanding Voltage Must meet 4-3 6-5 Temperature Cycling 5 cycles of: a) -55℃ 30 minutes b) +85℃ 30 minutes (Based upon JIS C0025) Appearance No Damage. Contact Resistance 20mΩ (Max.) 6-6 Salt Spray Tin-plated 12 hours / Gold- plated 24 hours exposure to a salt spray from the 5±1% solution at 35±2℃. (Based upon JIS C0023/MIL-STD-202 Method 101D Cond. B) 6-7 SO2 Gas 24 hours exposure to 50±5ppm. SO2 gas at 40±2℃. 6-8 NH3 Gas 40 minutes exposure to NH3 gas evaporating from 28% Ammonia solution. 6-9 Solderability Soldering Time: 5±0.5 sec. Solder Temperature: 245±5℃ Solder Wetting 95% of immersed area must show no voids, pin holes 6-10 Resistance to Soldering Heat (DIP) Solder pot method Soldering time: 10±0.5 sec. Solder Temperature: 260±5℃ Solder iron method Soldering Time: 5±0.5 sec. Solder Temperature: 370℃ ~ 400℃ Appearance No Damage. 6-11 Resistance to Soldering Heat (SMT) When reflowing Refer to paragraph 8 Solder iron method Soldering Time: 5±0.5 sec. Solder Temperature: 370℃ ~ 400℃ Appearance No Damage. 7. Crimp Specifications & Actuator Insertion/Withdrawal Force 7-1 Terminals with height, suggestion pressure width and wire and terminal's retention Wire Diameter Numbers Conductor Parts(Core Wire)mm Insulation Parts(PVC)mm Width Height Width Height AWG#24 A2001 1.20±0.10 0.75±0.05 1.60(Max.) 2.00(Max.)REF. AWG#26 0.70±0.05 AWG#28 0.65±0.05 AWG#30 0.60±0.05 7-2 [Unit : kgf] Circuits At Initial Circuits At Initial Insertion (Max.) Withdrawal (Min.) Insertion (Max.) Withdrawal (Min.) Single 0.70 0.10 10 6.50 1.60 02 2.50 0.80 11 7.00 1.60 03 3.00 0.80 12 7.50 1.80 04 3.50 1.00 13 8.00 2.00 05 4.00 1.00 14 8.00 2.00 06 4.50 1.20 15 8.00 2.00 07 5.00 1.20 16 8.50 2.20 08 5.50 1.40 17 8.50 2.20 09 6.00 1.40 18 8.50 2.20

12-year Experience of Manufacturing Connectors
Established in 2004, Xinpei is your reliable supplier for most of connectors. Our products are widely trusted by reputable and famouse manufacturers of household appliances, computer peripherals, medical equipment, locomotives, telecommunication device and other relative field.

Offering One-stop Sourcing Solutions for International Buyers
At our ISO 9001:2008 certified factory in Dongguan, mainland China, we make UL-listed goods by using automatic equipment for uniform product quality. By our integrated molding, mass production and assembly services are carried out by 100 skilled workers and the professional account executive can offer an one-stop sourcing solution to all international buyers.

Advanced Machines from Japan and Taiwan
We use advanced machinery from Japan and Taiwan to guarantee efficient and precise manufacturing. We have a commitment in delivering superior quality products at competitive prices.

Our advantages are as following:

• We offer complete end-to-end customized manufacturing solutions
• We have four mechanism engineers to refine your design for production
• We skillfully use AutoCAD, SolidWorks and Pro/E software to design your customized project
• Our materials are sourced from Switzerland, Japan and Taiwan
• Reputable manufacturers like Amphenol and AOC trust and cooperate with us for many years
• We own advanced inspection equipment like X-ray testing machine, high pressure testing machine projector, fully automatic tension meter, salt spray testing machine, insulation pressure testing machine and 3D optical image measuring testers to ensure the highest quality possible
• We accept small quantity orders
• Reply inquiries within eight hours
• We have more than 15 years of experience in handling OEM and ODM orders

Contact Us Now
We are looking forward to establishing long-term business relationship with you in the near future. So please inquire to us today and receive our fast reply within eight hours.